Aluminum Hinges Tapered Hole Type

Brand :

MISUMI

Caution

Product Description

Product Overview

Economy series aluminum butterfly Flat Hinges with countersunk holes.The products in this series are aluminum butterfly Flat Hinges with countersunk holes, with surface clear anodizing and black anodizing available for selection based on the actual needs.
Note: Among Flat Hinges with the same dimensions and specifications in this series, there are small aluminum ones with higher loads available for selection. For details, refer to the relevant products

Dimensional Drawing

Material Table

Product Material and Surface Treatment Overview:

TYPE	Material	Surface Treatment
C-HHFL	A6063-T5 Bushing: Polyacetal	Clear Anodized
C-HHBFL	A6063-T5 Bushing: Polyacetal	Black Anodized

Specification Table

Part Number		Number of holes	*Allowable Load		Mass	L	W	K	P	J	S	N		T	E	R
Type	No.		kg	N	g							Through Hole	Counterbored Hole
C-HHFL (Clear Anodized)	5	2	8	78	24	47	35.4	11	25	7.2	21	5.5	11	3.5	5.5	5
		3	15	147	50	66		8
	6	2	8	78	30	47	48	8.5	30	8	32	6.5	13		6	5.5
		3	15	147	70	78		9
	8	2	8	78	50	63	62	13	37	10	42
		3	15	147	110	113		13.5	43
	8－45	2	12	118	72	63	80	10		16.5	47			4.5
C-HHBFL (Black Anodized)	5	2	8	78	24	47	35.4	11	25	7.2	21	5.5	11	3.5	5.5	5
		3	15	147	50	66		8
	6	2	8	78	30	47	48	8.5	30	8	32	6.5	13		6	5.5
		3	15	147	70	78		9
	8	2	8	78	50	63	62	13	37	10	42
		3	15	147	110	113		13.5	43
	8－45	2	12	118	72	63	80	10		16.5	47			4.5

* The allowable load is the value when 2 pieces are used.

Precautions

To install the hinge on the panel, etc., it is recommended to choose the nut for the butterfly Flat Hinges. For details, you can search TYPE: HHPNT or HHPFNT in the website to choose according to the size requirements.

Usage Method

According to the weight of the door body where the Flat Hinges is mounted, the load-carrying capacity of the hinge can be calculated.
Determine the utilization direction first, and calculate according to the length and width of the door body

Utilization Method	Lengthwise Utilization		Lateral Utilization
	A=2XB	A≠2XB	-

Allowable Load Calculation Formula	Allowable Load =W	Allowable Load =W(B/A)*2	Allowable Load =W

Example of Use

Depending on the profile to be fixed, the selectable Flat Hinges specifications can be determined by the allowable load weight.For details, refer to the following table for the applicable hinge model.

Flat Hinges common combinations of aluminum profiles can be confirmed and found from the table below.

Representative Dimensional Drawing	Type of Matching Profile	Suitable Profile	* Allowable Load		Product Model	Surface Treatment	Mounting Pitch S mm
			KG	N
	Profile of the Same Size on Two Sides	Link 20/20 Profile	8	78	C-HHFL5	Clear Anodized	21
					C-HHBFL5	Black Anodized
			10	98	HHPSN5	Clear Anodized
					HHPBSN5	Black Anodized
			20	196	C-HHDL5	Clear Anodized
					C-HHBDL5	Black Anodized
		Link 30/30 Profile	8	78	C-HHFL6	Clear Anodized	32
					C-HHBFL6	Black Anodized
			10	98	HHPSN6	Clear Anodized
					HHPBSN6	Black Anodized
			20	196	C-HHDL6	Clear Anodized
					C-HHBDL6	Black Anodized
		Link 40/40 Profile	8	78	C-HHFL8	Clear Anodized	42
					C-HHBFL8	Black Anodized
			10	98	HHPSN8	Clear Anodized
					HHPBSN8	Black Anodized
			20	196	C-HHDL8	Clear Anodized
					C-HHBDL8	Black Anodized
		Link 45/45 Profile	12	118	C-HHFL8-45	Clear Anodized	47
					C-HHBFL8-45	Black Anodized
			15	147	HHPSN8-45	Clear Anodized
					HHPBSN8-45	Black Anodized
			30	294	C-HHDL8-45	Clear Anodized
					C-HHBDL8-45	Black Anodized
	Profile with Different Sizes on Two Sides	Link 20/30 Profile	8	78	C-HHFLS6-5	Clear Anodized	26.5
			10	98	HHPSF6-5
			20	196	C-HHDLS6-5
		Link 30/40 Profile	8	78	C-HHFLS8-5		31.5
			10	98	HHPSF8-5
			20	196	C-HHDLS8-5
		Link 20/45 Profile	8	78	C-HHFLS845-5		34
			10	98	HHPSF845-5
			20	196	C-HHDLS845-5
		Link 20/40 Profile	12	118	C-HHFLS8-6		37
			15	147	HHPSF8-6
			30	294	C-HHDLS8-6
		Link 30/45 Profile	12	118	C-HHFLS845-6		39
			15	147	HHPSF845-6
			30	294	C-HHDLS845-6