Pivot Pins Straight, Retaining Ring

The hinge pin can be used as the pivot point of various rotary connection mechanisms. The pivot point is similar to the axis of a hinge, and the connected parts can make rotary movements.

*Dg7 tolerance is limited to the L dimension part, and others are negative tolerances.
This type may have centering holes depending on dimensions.
E-CCG·E-PCCG have identification grooves on the side in order to distinguish them from the hardened type.

・Material Table

Type	Equivalent Material	Hardness	Surface Treatment	Accessories
L Dimension Configurable
E-CCG	General structural steel or carbon steel	-	Ferroferric Oxide Protective Film	2 Retaining Rings
E-CCGH		HRC40～
E-PCCG		-	Electroless Nickel Plating
E-PCCGH		HRC40～
E-GCCG		Plating hardness 750HV～	Hard Chrome Plated
E-SCCG	Austenitic stainless steel	-	-
E-SCCGH	Martensitic stainless steel	HRC45～
E-GSCCGH		HRC45～ Plating hardness 750HV～	Hard Chrome Plated

If there are requirements for rust prevention, give priority to products made of austenitic stainless steel, hard-chrome plated products or those with surface treatment of electroless nickel plating.

Part Number		L Selection	m		N	d
Type	D	L Dimension Configurable (0.1mm increments)		Tolerance			Tolerance
L Dimension Configurable E-CCG E-CCGH E-PCCG E-PCCGH E-GCCG E-SCCG E-SCCGH E-GSCCGH	2	5.0~30.0	0.5	+ 0.05  0	2	1.5	+ 0.06  0
	3	5.0~50.0				2
	4		0.7	+ 0.1  0		3
	5	10.0~60.0				4	+ 0.075  0
	6	10.0~100.0				5
	8		0.9		3	7	+ 0.09  0
	10	15.0~100.0	1.15	+ 0.14  0		9.6	0 - 0.09
	12	15.0~150.0			4	11.5	0 - 0.11
	13	25.0~150.0				12.4
	14					13.4
	15					14.3
	16	30.0~150.0				15.2
	17					16.2
	18		1.35			17
	20					19	0 - 0.21
	22					21
	25					23.9

E-SCLGHN may be discolored due to hardening.
For JIS engineering specifications of the supplied retaining ring, refer to Retaining Ring Specifications

Feature 1: It has a tolerance of g7 and is used in conjunction with bearings.
Feature 2: Available in various shapes. The shapes include straight cotter pin type, straight retaining ring type, shouldered cotter pin type, shouldered retaining ring type, shouldered lock nut type, set screw type, shouldered set screw type, and both ends tapped type.
Feature 3: Products made of stainless steel (austenitic stainless steel) with excellent anti-rust performance and products with the surface treatment of hard-chrome plating or electroless nickel plating are available for selection to solve the problem of rusting.
Feature 4: L Dimension Configurable type, freely selectable in 0.1mm increments to accommodate different use environments.
Feature 5: The L Dimension Fixed type is available at a relatively low price.

①Dg7 tolerance is limited to the L dimension range. Others are general tolerances.
②Anti-rust specification selection and maintenance.
If there are requirements for rust prevention, give priority to products made of austenitic stainless steel, products with surface treatment of hard chrome plating or those with surface treatment of electroless nickel plating.
 Products without surface treatment need to be applied antirust oil regularly for maintenance.
③This product comes with 2 retaining rings, so take care to avoid missing upon receipt.
④Alteration is only applicable to the L dimension configurable type.