SURUGA SEIKI Holder

• 

  LD Holder (Chip Carrier Type)

  SURUGA SEIKI

  [Features]
  · A Chip Carrier type LD holder with a built-in Peltier element.
  · Features a built-in Peltier element, and a calibrated 10kΩ thermistor sensor.
  · The switching for the anode/cathode of the LD can be configured by replacing the jumper pins.
  · There are two types of Chip Carrier LD holder. Configure according to the mounting (output) direction of the LD.
  · For connectors, a D-sub9 pin female is used for driving the LD, and a D-sub9 pin male is used for the temperature controller.
  · The F129-1 water cooling adapter is also available.
  · Use a low temperature circulating water tank or similar to enable greater stabilization and for even lower temperatures.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  3-axis lens holder

  SURUGA SEIKI

  [Features]
  · The B11-40C is employed for the X-axis while the optical axis is configured at 45 mm.
  · Replace the lens and/or adapter to allow for use in different types of application.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  5-axis lens holder

  SURUGA SEIKI

  Replace the lens and/or adapter to allow for use in different types of application. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  LD Holder

  SURUGA SEIKI

  F511L: fixed type. F512L, F513L: YZ axis adjustable LD holder. Select according to the number of pins and the pin pitch (pin P.C.D.) of the LD.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  LD holder (To-Package type)

  SURUGA SEIKI

  [Features]
  · A To-Package type LD holder with a built-in Peltier element.
  · Features a built-in Peltier element, and a calibrated 10kΩ thermistor sensor.
  · Supports LD sizes of ø5.6 (Pin PCD, 2.0) and ø9.0 (Pin PCD, 2.54) for three-pins and for four-pins respectively.
  · For common anodes and common cathodes, etc., configure by replacing the jumper pins.
  · For connectors, a D-sub9 pin female is used for driving the LD, and a D-sub9 pin male is used for the temperature controller.
  · The F129-1 water cooling adapter is also available.
  · Use a low temperature circulating water tank or similar to enable greater stabilization and for even lower temperatures.

  CAD ：

  2D / 3D

  Days to Ship:	12 Day(s) or more

• 

  Screw Ring

  SURUGA SEIKI

  A threaded ring for fixing lenses and mirrors. Note that even when the diameters are the same, the shapes can differ depending on the product. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	12 Day(s) or more

• 

  Polarizer holder with tilt

  SURUGA SEIKI

  A holder that can retain items such as polarizing plates and wave plates. It can also rotate (θx) and tilt them (θy, θz). Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Alignment target

  SURUGA SEIKI

  Can be used for optical system constructions.
  
  [Features]
  · Used for adjusting the optical axis when building an optical system for the Opt Station.
  · Push-down the large target-fixing pin to fix to the tapped hole on the plate board.
  · Return the pin upward to install in any position.
  · The mark on the target is adjusted to a height of 45 mm.
  · Target stickers (black cross on a white base / white cross on a black base) are included.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Camera holder (F119-2)

  SURUGA SEIKI

  A holder for fixing cameras, CCD cameras, and vidicon cameras, etc. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	16 Day(s) or more

• 

  Adapter for connector

  SURUGA SEIKI

  [Features]
  · An adapter for optical fiber connectors.
  · An FC type receptacle is included as standard, so please select according to the connector.
  · The FC type receptacle is designed so that when a connector is inserted, the end surface of the ferrule extends about 0.5 mm from the receptacle surface. Ideal for placing in close proximity to other items.

  CAD ：

  2D / 3D

  Days to Ship:	16 Day(s) or more

• 

  Sensor/laser holder

  SURUGA SEIKI

  [Features]
  · Can adjust the tilt angle of small sensors and laser pointers.
  · P.C.D.32 tapped holes are included on the holder surface. Uses these to mount various types of adapter plate.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Pinhole Adapter

  SURUGA SEIKI

  Used by attaching to various types of cross motion holder. The applicable diameter of the pin hole is ø16 mm. Attachment and detachment is carried out using a threaded ring system. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Prism Holder

  SURUGA SEIKI

  [Features]
  · Configured so that the optical axis height is at the center of the element when the element is 20 mm, and standardized at 25 mm from the bottom.
  · Move the upper sliding part to fix the prism.
  · Use the upper knob to fix without having to move the element.
  · The F551-20 bottom plate features M4 tapped holes. Mount a rod to change to a rod type.
  · F552-20 can be finely adjusted.
  · The elements are positioned using the pins in the three locations.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Mirror Holder

  SURUGA SEIKI

  An affordable mirror holder for fixing items such as mirrors or plate beam splitters. The tilt can be finely adjusted in the two axial directions. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	12 Day(s) or more

• 

  Ring Wrench (A92)

  SURUGA SEIKI

  A ring wrench for tightening threaded rings. Variable types and fixed types are available in sizes to fit different ring diameters. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D

  Days to Ship:	13 Day(s) or more

• 

  Adapter for polarizer prism

  SURUGA SEIKI

  An adapter that can retain polarizing prisms and other similar items. Can be mounted to polarizer holders. Can be mounted to holders for F62, F63 and F64 elements which have a diameter of ø30.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Polarizer holder

  SURUGA SEIKI

  [Features]
  · A holder used for retaining and rotating polarizing plates, polarizing filters, and wave plates, etc.
  · Can be manually rotated 360°.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Cross movement holder plate type

  SURUGA SEIKI

  [Features]
  · A holder that can support and fix various types of adapter, and finely adjust them in the YZ axes and Yzθyθz axes.
  · A plate type cross motion holder with good stability and which can be used for experiments with low optical axes.
  · 0.5 mm screws are used for the fine movement parts.
  · For the F02-1E type, fine movement of the YZ axes can be made using the operating screw. For the F02-4E type, fine movement of the Yzθyθz axes can be made

  CAD ：

  2D / 3D

  Days to Ship:	12 Day(s) or more

• 

  Variable slit

  SURUGA SEIKI

  [Features]
  · A double door type variable slit.
  · The slit width is adjusted using the micrometer head.
  · The slit width and the position of the center are constant.
  · V-groove rails and cross rollers are used for the double door slit section guide, decreasing the tilt of the slits during operation.
  · Use a Hartmann plate to adjust the slit height.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Fixed-type Holder

  SURUGA SEIKI

  Can retain and fix various types of adapter. The optical axis height is standardized at 25 mm from the bottom. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	16 Day(s) or more

• 

  Fine Adjustment Prism Holder

  SURUGA SEIKI

  Can rotate prisms, cube beam splitters, and similar other objects and tilt them in the two axes. Prisms are fixed using the slide clamp screw on the upper part and an element clamp screw.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Polarizer holder with fine adjustment

  SURUGA SEIKI

  [Features]
  · A holder consisting of the F62 type polarizer holder with additional fine adjustment functionality.
  · Allows for 360° coarse movement with the clamp loosened. With the clamp tightened, it can perform micro adjustments on the micrometer head to ±4°.
  · The F63-30N can be fitted with the F69polarizing prism adapter.
  · The scale is structured in a way that allows zero point alignment, and so can be set to any angle from the reference angle.
  · Calculating the optical axis of the rod stand.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Resin ring

  SURUGA SEIKI

  [Features]
  · A product for fixing lenses and mirrors to holders by the manufacturer.
  · Note that this product has been designed exclusively for holders from the manufacturer.
  · Note that even when the diameters are the same, the shapes can differ depending on the product.

  CAD ：

  2D / 3D

  Days to Ship:	12 Day(s) or more

• 

  Centering Lens Holder: For Collimate Lens, Stability and Operability Emphasized Type

  SURUGA SEIKI

  [Features]
  · Can be used for the construction of optical systems.

  Days to Ship:	13 Day(s) or more

• 

  Self-centering Lens Holder: for Collimating Lens Precision Cross Roller Type

  SURUGA SEIKI

  [Features]
  · Can be used for the construction of optical systems.

  Days to Ship:	13 Day(s) or more

• 

  Centering Lens Holder: Single Lens Stable Operation Focusing Type

  SURUGA SEIKI

  Can be used for optical system constructions. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Centering lens holder: for Objective lens Fixed Type

  SURUGA SEIKI

  [Features]Inexpensive optical holder with no adjustment mechanism. [Applications]It can be used for optical experiments.

  CAD ：

  2D / 3D

  Days to Ship:	16 Day(s) or more

• 

  Centering Lens Holder: Objective Lens Stable Operation Focusing Type

  SURUGA SEIKI

  [Features]
  · Can be used for the construction of optical systems.
  · When using objective lenses with large outer diameters. The F504-40 series high rigidity cross motion holder is recommended.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Centering Lens Holder: Objective Lens Precision Cross Roller Type

  SURUGA SEIKI

  [Features]
  · Can be used for the construction of optical systems.
  · When using objective lenses with large outer diameters. The F504-40 series high rigidity cross motion holder is recommended.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  High Rigidity Cross Movement Holder

  SURUGA SEIKI

  A precision cross motion holder that can support and hold various types of adapter, and finely adjust them in the YZ axes. Includes a direct lock mechanism that can directly fix the movable parts. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  High Performance Cross Motion Holder

  SURUGA SEIKI

  Can be mounted with various types of adapter and then finely adjust them in the YZ axes. Capable of a smooth and straight feed. Designed with an optical axis height of 25 mm from the bottom. For use with the Opt Station.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

• 

  Filter Holder (F72-1)

  SURUGA SEIKI

  [Features]
  · A holder for setting round and square type filters.
  · Can be fitted with up to four filters with external diameters of ø50 mm.
  · Filters are inserted from the top, but as they are only placed down, they can be angled depending on the filter thickness.

  CAD ：

  2D / 3D

  Days to Ship:	16 Day(s) or more

• 

  Filter Holder (F561)

  SURUGA SEIKI

  [Features]
  · A holder for setting filters with diameters of ø15 mm or ø20 mm.
  · The optical axis height is standardized at 25 mm from the bottom.
  · Can be fitted with two filters.
  · Fix by loosening the clamp and sliding the holding part backwards or forwards in line with the thickness of the filter.
  · Filters with a thickness of up to 4 mm are supported.
  · The bottom plate features an M4 tapped hole. Mount a rod to change to a rod type.
  · The F561-20 can also be used as a simplified polarizing element holder by directly turning the element.

  CAD ：

  2D / 3D

  Days to Ship:	13 Day(s) or more

Loading...