Dial Gauges（Display Method：Dial Page2）

• 

  Stone Dial Comparator

  OBISHI KEIKI SEISAKUSHO

  [Features]
  · Equipped with a fine motion mechanism that makes it easy to move a very small dial gauge.
  · The base was manufactured using high quality black gabbro.
  · Minimal secular change and temperature fluctuations, with excellent hardness and wear resistance.

  Days to Ship:	25 Day(s) or more

• 

  Dial comparator (PH-2 type)

  OBISHI KEIKI SEISAKUSHO

  Comes with 2 brackets. It is ideal for measuring pipes and other wall thickness. Has cast iron base.

  Days to Ship:	25 Day(s) or more

• 

  Dial comparator (PH-3 type)

  OBISHI KEIKI SEISAKUSHO

  [Features]
  · A hardened plate with relief grooves is installed to the top surface of the base.
  · The arm can be inserted and removed, enabling measurement at any position on the base board surface.

  Days to Ship:	10 Day(s) or more

• 

  Standard Shaped Dial Gauge (Scale Interval: 0.005 mm)

  OZAKI MFG (PEACOCK)

  [Features]
  · The most widely used dial gauge with scale intervals of 0.001/0.005 mm.
  · Select from a wide range of devices to suit the application.
  · With an O-ring used to prevent ingress of water or oil from the gap between the external and internal frames, it features excellent waterproofing.
  · By using SK hardened steel, the stem possesses a high strength that is resilient even for severe use.
  · Gears are protected from sudden upward pressure from the spindle by the shock proofing mechanism.
  · Limit stickers are included as standard with all models.

  Days to Ship:	14 Day(s) or more

• 

  Surface Dial, New Peak Test (D Series)

  OZAKI MFG (PEACOCK)

  [Features]
  · The display is enlarged by approximately 30% for better visibility.
  · The long stem (screw-in type) has been standardized.
  · Select from 0.01 mm, 0.002 mm, or 0.001 mm types.
  · The gauge damage prevention probe is provided on all models.
  · D type in which the display can be seen clearly even from a distance.
  · Surface diameter φ46.5.
  · Easy to read the minimum display.

  Days to Ship:	14 Day(s) or more

• 

  New Pic-Test (without Stem, V-Series)

  OZAKI MFG (PEACOCK)

  Miniature bearings are used for the bearings of the fulcrum portion of the gauge heads to reduce the effects of rod play and achieve excellent indicating stability.

  Days to Ship:	14 Day(s) or more

• 

  New Pic Test for Low Pressure (E Series)

  OZAKI MFG (PEACOCK)

  [Features]
  · Lever-type dial gauge with super low pressure measuring force (0.05 N / 0.1 N).
  · No-clutch type (PCN) and switching lever type (PC) are available as a selection of 0.01 mm or 0.002 mm options.
  · Uses a green scale plate that is easy on the eyes.
  · Highly sensitive, enabling measurement at low measurement power.
  · The gauge damage prevention probe is provided on all models.
  · By adopting a balancing needle, errors due to difference in posture (gauge mounting direction) are minimized.
  · Try it out if you are having trouble with errors due to the effects of measuring force

  Days to Ship:	16 Day(s) or more

• 

  Pictest (Double Sided Type, W Series)

  OZAKI MFG (PEACOCK)

  A double-sided lever type dial gauge that is very useful for work piece centering measurement. It is provided with a gauge damage prevention measurement probe. By adopting a balancing needle, errors due to difference in posture (gauge mounting direction) are minimized.

  Days to Ship:	19 Day(s) or more

• 

  Pictest (without Stem, V Series)

  OZAKI MFG (PEACOCK)

  Miniature bearings are used for the bearings of the fulcrum portion of the gauge heads to reduce the effects of rod play and achieve excellent indicating stability.

  Days to Ship:	14 Day(s) or more

• 

  Pic Test for Low Pressure (E Series)

  OZAKI MFG (PEACOCK)

  [Features]
  · Lever-type dial gauge with super low pressure measuring force (0.05 N / 0.1 N).
  · No-clutch type (PCN) and switching lever type (PC) are available as a selection of 0.01 mm or 0.002 mm options.
  · Uses a green scale plate that is easy on the eyes.
  · Highly sensitive, enabling measurement at low measurement power.
  · The gauge damage prevention probe is provided on all models.
  · By adopting a balancing needle, errors due to difference in posture (gauge mounting direction) are minimized.
  · Try it out if you are having trouble with errors due to the effects of measuring force

  Days to Ship:	14 Day(s) or more

• 

  0-0 PIC-Test (PCC Series)

  OZAKI MFG (PEACOCK)

  [Features]
  · The 0-0 Pic Test is a dedicated device for centering, parallelism, and other referencing work.
  · Moreover, it is a low priced product.
  · The scale plate of the 0-0 Pic Test is only for zero point, so it can be mounted with probes of varying lengths and shapes depending on the desired use.
  · Pointer rotation is set at less than one full rotation to eliminate reading error.
  · The gauge damage prevention probe is provided on all models.
  · Gauge heads are not affected by angle errors caused by the contact angle

  Days to Ship:	18 Day(s) or more

• 

  Dial Swift Gauge

  OZAKI MFG (PEACOCK)

  A dial-type thickness (outer diameter) measuring device which can be used in the same way as a micrometer. To measure, push down the knob with a finger and clamp the measuring object.

  Days to Ship:	18 Day(s) or more

• 

  Dial Gauge, Dial Lens Gauge

  OZAKI MFG (PEACOCK)

  Easy measurement of the thickness of rough surfaces, crescent-shaped lenses, or flat surfaces. Replace the gauge head and anvil to measure plane thickness. Flat probe included.

  Days to Ship:	14 Day(s) or more

• 

  Dial Pipe Gauge

  OZAKI MFG (PEACOCK)

  Suitable for measuring the inner thickness of pipe shapes and the thickness of curved workpieces. Special shapes can also be manufactured for the gauge heads and anvil part.

  Days to Ship:	14 Day(s) or more

• 

  Dial Sheet Gauge

  OZAKI MFG (PEACOCK)

  [Features]
  · Ideal for measuring the thickness of paper, urethane, vinyl, rubber, etc.
  · There are 3 types of measurement depths (insertion depths), 300 mm, 500 mm, and 690 mm, allowing for easy measurement of thickness even for large workpieces

  Days to Ship:	14 Day(s) or more

• 

  Dial Inside Gauge Replacement Lot for U Series

  OZAKI MFG (PEACOCK)

  A replacement rod for use with the U Series Dial Inside Gauge.
  
  [Features]
  · Ideal for measuring the internal diameters of relatively large holes and internal wall surfaces.

  Days to Ship:	20 Day(s) or more

• 

  Dial Caliper Gauge LB (Inner) Type

  OZAKI MFG (PEACOCK)

  [Features]
  · A simple measuring instrument ideal for measuring the inner diameter and groove width of parts generally considered to be difficult to measure.
  · Choose from a wide range of models with scale intervals of 0.1 mm and 0.01 mm.
  · LB-7.
  · Handy moving frame type.
  · LB-7S.
  · Handy moving frame type.
  · LB-7V.
  · Handy moving frame type.
  · Various special products have been created to suit various applications. Contact us for details.

  Days to Ship:	14 Day(s) or more

• 

  Dial Comparator PH2

  RIKEN KEISOKUKI

  [Features]
  · The flatness of the measuring surface is 0.01 mm.
  · The measuring surface has a precise ground finish.
  · Convenient for measuring curved workpieces.
  · The dial gauge is installed by clamping the back part of the back cover.

  Days to Ship:	14 Day(s) or more

• 

  Dial Comparator PH3B

  RIKEN KEISOKUKI

  [Features]
  · The flatness of the measuring surface is 0.01 mm.
  · The measuring surface has a precise ground finish.
  · The dial gauge mounting hole is φ8.

  Days to Ship:	8 Day(s)

• 

  Dial comparator T type

  RIKEN KEISOKUKI

  [Features]
  · The flatness of the measuring surface is 0.002 mm.
  · Stone base does not rust, has incredible wear-resistance, and can be maintained easily.
  · The dial gauge mounting hole is φ8.

  Days to Ship:	12 Day(s)

• 

  Dial Comparator MM2

  RIKEN KEISOKUKI

  Measurement surface flatness is 0.01 mm. Measurement surface has a precision ground finish.

  Days to Ship:	15 Day(s) or more

• 

  Dial Indicator Measurement Range 0 to 0.2 mm Probe Ruby

  NIIGATA SEIKI (SK)

  Abrasion-resistant non-conductive dial indicator.
  [Features]
  · Measurements can be taken easily in places that cannot be measured using a dial gauge, such as in narrow or deep spaces.
  · A jewel has been assembled to each bearing for excellent precision and durability.
  · A ruby ball is used in the gauge head to provide excellent abrasion resistance. It does not conduct electricity and does not become magnetically charged.
  · The main unit is made of steel.
  [Applications]
  · Used to measure inner/outer sides, groove width, centering, parallelism, flatness, etc.

  Days to Ship:	1 Day(s)

• 

  Precision Dial Indicator

  MAHR

  Days to Ship:	12 Day(s) or more

• 

  Precision Small Dial Indicator

  MAHR

  Days to Ship:	12 Day(s)

• 

  Dial Caliper Gauge

  NIIGATA SEIKI (SK)

  Days to Ship:	1 Day(s)

• 

  Dial Indicator

  NIIGATA SEIKI (SK)

  Days to Ship:	1 Day(s)

Loading...